kpilogo shields

Morphological and structural properties of laminates consisting of extruded sheets of liquid crystalline polymer (LCP)/poly(ethylene terephthalate) (PET) blend were investigated. In laminates obtained by compression moulding the two blend sheets with the extrusion directions at right angles, the LCP fibril axes lay in various directions in the PET matrix, and consequently they looked like mechanically isotropic materials.

Детальніше...  

A detailed study on the dependence of the dispersed phase size versus the concentration of interfacial modifier is undertaken for an immiscible blend system, polyamide/polyolefin modified with a polyethylene copolymer ionomer. The resulting curve is known as an emulsification curve, and evidence is presented which indicates that the point of interfacial saturation of an interfacial modifier on the dispersed phase can be estimated from these data. The characteristic shape of the emulsification curve displays an initial rapid drop in phase size, as would be expected for a system experiencing a drop in interfacial tension. A critical concentration value of interfacial modifier (C,a) is subsequently observed, beyond which a quasiequilibrium particle size is obtained. The Ccrit value is directly related to the interfacial area of the dispersed phase and a lower equilibrium dispersed particle size results in a corresponding shift in Ccr, for similar systems. The area occupied per molecule, calculated using the Co,it value and assuming, as an extreme limit, that all modifier is at the interface, is 5 nm 2 per molecule. The area value is in the appropriate range expected for a system with a saturated interface

Детальніше...  

The X-ray structure analysis of isotactic poly(methyl methacrylate) was performed by adopting the 10/1 double-stranded helix model as the molecular model, and the crystal structure analysis, which has remained as an unsettled problem for a long time, has been brought to an end. The crystals are orthorhombic, with rather large cell dimensions, i.e. a=41.96, b=24.34, and c (fibre axis)=10.50 A. There are eight 10/1 double-stranded helices of the right-handed and left-handed senses in the unit cell, which take up a slightly complicated hexagonal-like closest packing-mode, and where among the first six neighbour helices the two same-handed senses are located at z = c/2 and the four opposite-handed senses are located at z = c/4 and 3c/4. The space group is Fddd-D2h 24 for the disordered structure, which is composed of upward and downward helices related by a twofold rotation axis perpendicular to the helix axis. This complicated helical packing-mode originates from (i) the fact that iPMMA as synthesized is an apparently racemic polymer, and (ii) the fact that two molecular chains form a robust and rod-like 10/1 double-stranded helix.

Детальніше...  

Blends of poly(butylene terephthalate) (PBT)/high density polyethylene (HDPE)/ionomer (IONO) polymers, at a blending ratio of 76/19/5 (by weight), were reinforced with short glass fibres (GFs) at levels of 10-30 wt % in order to enhance the mechanical properties for load-bearing engineering applications. The melting and crystallization behaviour of the composites, studied by differential scanning calorimetery (d.s.c.), indicate the presence of an increase in crystallinity in the presence of the glass fibres. Dynamic mechanical thermal analysis (d.m.t.a.) shows that the introduction of glass fibres reduces damping to a greater extent than would be expected theoretically. Incorporation of glass fibres increases the storage modulus, when compared to the unreinforced system, at all temperatures studied. The presence of short glass fibres increased the melt viscosity and decreased the extrudate swell, with the effect being more pronounced at higher temperatures. Rheological data have been analysed on the basis of fibre length (or aspect ratio) and/or distribution of the fibre lengths by using the rheological model proposed by Maron and Pierce.

Детальніше...  

Solutions of poly(methyl methacrylate) in 1-butanol demix on cooling. By solution extrusion, fibres are produced which have an oriented porosity. The relation between this morphology, the phase diagram and the extrusion procedure is discussed

Детальніше...  

A series of styrene-phenyl vinyl sulfoxide diblock copolymers was prepared using the 'living' anionic polymerization technique. The thermally labile phenyl vinyl sulfoxides undergo an elimination process to yield acetylene moieties at 150°C. The weight and volume of the iodine-doped conducting fractions were adjusted by changing the length of the styrene block. A sigmoidal composition-dependent conductivity and a maximum in the dielectric constant measurement near the threshold composition suggested a 'percolation-like' conducting process. In addition to electrical measurement, the block copolymers were also characterized by infra-red spectroscopy, thermal analysis, ~H n.m.r., and size exclusion chromatography

Детальніше...  

Formylated Novolacs were prepared by the reaction of Novolacs with formic acid-acetic anhydride in the presence of pyridine in tetrahydrofuran at room temperature. When the resulting formylated Novolacs films were exposed to deep-ultra-violet light, photochemical decomposition of the formyl group was observed. This reaction generates Novolacs through decarbonylation of the formyi radical, which is formed in the first stage of the photo-Fries rearrangement. More than 50% of the formyl groups decomposed after an exposure of approximately 500 mJ cm- 2. Both negative and positive tone images can be manufactured by developing these films with a suitable solvent

Детальніше...  

The effect of thermal history on the phase behaviour and viscoelastic relaxations of poly(triethylene glycol p,p'-dibenzoate) (PTEB) was studied. The mesophase of PTEB can be converted into a three-dimensional crystal by annealing at appropriate temperatures and for appropriate times. Three PTEB samples were analysed, one of them freshly quenched from the melt and the other two annealed under different conditions (room temperature and 85~C). The phase structure was investigated by differential scanning calorimetry and X-ray diffraction, both at wide and low angles (using synchrotron radiation in the latter case). This structure affects slightly the fl and 7 relaxations, whereas the glass (~t) transition is more intense and narrow and appears at a lower temperature for the sample freshly quenched from the melt, which exhibits only the liquid crystalline phase.

Детальніше...  

Phase transfer technique, using benzyldimethylhexadecylammonium chloride as a titrant, was employed for the characterization of non-crosslinked natural rubber latex. The critical transfer concentration values were reproducible in each solvent studied and the increase was found to coincide with the decrease of the difference between the solubility parameter of organic solvent and that of natural rubber. Results indicated a complete phase transfer process in which 96% of rubber was transferred.

Детальніше...  

A novel method for the conversion of sulfonium precursor into poly(p-phenylene vinylene) (PPV) has been developed. The treatment of the sulfonium precursor with strong acids at room temperature leads to doped PPV. The materials obtained have the same optical properties and slightly higher conductivity in comparison to PPV prepared by pyrolysis of the precursor. Finally, the chemically converted PPV material appears to be of lower density, therefore the dopants can easily diffuse into the polymer matrix and subsequently enhance the electrical conductivity of the system.

Детальніше...  

Корисні статті

Хто такий інженер

Інженер - професія нелегка, але одночасно з цим дуже цікава і захоплююча. Адже інженер це людина, у якого народжуються в голові нові ідеї і тому він здатний винаходити.

У багатьох виникає питання: хто такі інженери? Інженер (франц. Ingénieur) - фахівець з вищою технічною освітою. Спочатку інженерами називали людей, які керували військовими машинами. Поняття громадський інженер з'явилося в XVI столітті в Голландії, застосовано до сфери будівництва мостів і доріг, потім інженери з'явилися в Англії, а потім в інших країнах.

Інженер-конструктор

Хто такий інженер-конструктор? Даним питанням задаються багато людей, які бажають пов'язати своє життя з цією професією. Варто відзначити, що ця професія однією з найбільш високооплачуваних на сучасному ринку праці, яка характеризується високим попитом з боку роботодавців. Інженер-конструктор машинобудування повинен володіти аналітичним складом розуму, підвищеною уважністю до деталей і відповідальним підходом до роботи. Дана діяльність пов'язана з прорахунками і різноманітним обладнанням. Першокласний інженер-конструктор механік володіє також такими рисами характеру, як раціональність і ерудованість. Важливу роль відіграє стресостійкість, адже робочий процес є досить трудомістким і при потребі замовника вимагає готовності швидко вносити зміни в готові креслення.

Хімічне машинобудування

Хімічне машинобудування багатопрофільна галузь машинобудування, що поєднує в собі природні та експериментальні науки (наприклад, фізика і хімія), разом з науками про життя (наприклад, біологія, мікробіологія та біохімія). Математику та економіку вокористовують для розробки, перетворення, транспортування, управління виробничими процесами, які перетворюють сировину в цінні продукти.

ВНЗ України

Вища освіта є невід'ємним елементом перспективного кар'єрного росту, тому перед кожним абітурієнтом виникає проблема, в які інститути подавати документи. Варто відзначити, що в Україні існує велика кількість вузів. Всі навчальні заклади поділяються на державні та приватні, пропонуючи різноманітні освітні програми по різних профілів. Щоб пошук інститутів дав задовільні результати, слід визначитися з найбільш прийнятними спеціальностями. Також підбір університету передбачає вибір підходящої форми навчання, наявність високої акредитації у вузу і рівень його престижності.

Інженер-механік

Інженер-механік (від лат. Ingenium – талант, обдарованість, і mēchanicus – механік) – це технічний чи технологічний фахівець з вищою освітою, який застосовує отримані знання для конструювання, проектування, моделювання та експлуатації машин, апаратів та технічного обладнання в різних галузях сільського господарства та технічного виробництва. Першими з інженерів були саме механіки; вони розробляли і збирали різноманітні машини і механізми, в яких використовували принципи і закони механіки.